Cutting oils

esgeCut series

These non water-soluble coolants are used to optimise chip removal processes. They are used when focus is on lubrication. Cutting oils have special additives that facilitate adhering to surfaces or reaching a high pressure stability. Low-viscosity cutting oils are usually used for honing and grinding, medium-viscosity oils for drilling, turning and milling and oils with higher viscosities for difficult machining processes, such as broaching. The base oils of the esgemo product range were particularly chosen with regard to low emissions. On the one hand, this avoids health hazards to users, on the other hand, a higher cost-effectiveness is achieved by lower evaporation.
Different viscosities of our cutting oils adapt perfectly to individual demands – from non-ferrous metals to stainless steel. For each application, a technically efficient top performance can be achieved. Furthermore, our products are physiologically neutral, chlorine-free, low-emission and odourless.

esgeCut FBB 2200

esgeCut FBB 2200 is a multi-purpose oil based on high-quality, low-aromatics base oils. It can be used both as cutting oil and, in a rationalising way, for lubrication of machines and hydraulic systems. It contains substances that improve durability and corrosion protection. Additional EP agents increase mechanical resistance and improve cutting performance during chip removal processes.
esgeCut FBB 2200 produces low emissions and avoids contamination due to oil mist at the workplace. It is also free from chlorine and heavy metal. Preferred applications for this cutting oil are automatic lathes and multi-spindle lathes.
esgeCut FBB 2200 guarantees excellent surface qualities, adherence to tolerances due to low tool-wear as well as long tool lives. Long-term use of the oil filling is possible because no additives are discharged.
esgeCut FBB 2200 is suitable for non-ferrous metals and machining steel.

Technical data
Technical Data Value Test method
Density at 15°C g/ml 0,85 DIN 51 757
Viscosity at 40°C mm²/s 22 DIN 51 562
Flashpoint °C >190 DIN 51 758
Corrosive effect on copper Korr.Grad 1 – 100 A 3 DIN 51 376
All values are approximate values

esgeCut FBS 2200

esgeCut FBS 2200 cutting oil is made from specially selected base oils with various additives in different concentrations. It contains in combination polar active ingredients as well as special wear protection and aging and corrosion protection additives.
esgeCut FBS 2200 cutting oil is free of chlorine and zinc. The oil is mild in odor, physiologically harmless, light colors and does not tend to foaming even under unfavorable operating conditions; It is set low in oil mist.
esgeCut FBS 2200 cutting oil is used especially for alloyed materials for difficult cutting machining processes on machines for drilling, turning, milling and parting as well as for thread cutting.
esgeCut FBS 2200 cutting oil achieves high tool life at optimum cutting speeds and feed rates, excellent surface quality, dimensional stability and tool protection. It is tuned to the state of the art in terms of machining methods, tool types and the various materials.
esgeCut FBS 2200 cutting oil is suitable for non-ferrous metals and steel.

Technical Data
Technical Data Value Test method
Density at15°C g/ml 0,87 DIN 51 757
Viscosity at 40°C mm²/s 22 DIN 51 562
Flash point °C >190 DIN 51 376
Corrosive effect on copper Korr.Grad 1 – 100 A 3 DIN 51 376
Color 2 ASTM
All values are approximate values

Special cutting and deep drilling oil

esgeCut FBE 1100

esgeCut FBE 1100 special-Cutting oil is produced by a special process and consists of selected, low-evaporation base oils. In addition, it contains various additives in high dosage, such as sulfur compounds, polar active ingredients, special wear components, aging and corrosion protection.
esgeCut FBE 1100 special-Cutting oil is free of chlorine and heavy metals. It is mild in the odor, extremely tolerated by the skin, bright colors and neither tends to foaming nor to excessive oil mist formation even under unfavorable operating conditions.
esgeCut FBE 1100 special-Cutting oil is used on machines for drilling, turning, milling, parting off and thread cutting. Steels of all alloy grades and strengths, cast materials as well as stainless and acid-resistant steels are successfully machined. Especially for difficult, cutting-edge machining processes, it provides excellent tool life and protects tool cutting edges against increased wear. It guarantees excellent surface qualities and maximum dimensional stability.
With esgeCut FBE 1100 special-Cutting oil not only productivity will be increased significantly as well as costs will be significantly reduced too, but it will also take greater account of the safety needs of people, the environment and machines. It is also ideally suited for all deep hole drilling with single lip, BTA and ejector tools as well as full, core and drill of a wide range of materials.
esgeCut FBE 1100 special-Cutting oil corresponds to the state of the art; it is not suitable for nonferrous metals.

Technical data
Technical Data value Test method
Density at15°C g/ml 0,86 DIN 51 757
Viscosity at 40°C mm²/s 11 DIN 51 562
Flash point °C >160 DIN 51 376
Color yellow ASTM
Corrosive effect on copper Korr.Grad 4 – 100 A 3 DIN 51 759
All values are approximate values
Universal-Cutting Oil

esgeCut FBU 2200

esgeCut FBU 2200 Universal-Cutting-Oil is made from specially selected base oils, with various additives, in different concentrations. It contains, in combination, special high-pressure additives, polar active ingredients, special additives for protection against wear, oxidation stabilizers and anti-mist additives.
esgeCut FBU 2200 contains no chlorine and is free of PCB / PCT. The oil is yellowish to light brown, mild in odor and low fog.
esgeCut FBU 2200 it was specially developed for machining titanium, stainless steels and non-ferrous metals. Due to the very pressure-resistant lubricating film even difficult cutting machining processes on CNC-controlled machines are possible.
esgeCut FBU 2200 achieves high tool life at optimum cutting speeds and feed rates. In addition excellent surface-quality, dimensional accuracy and tool protection. It is tuned to the state of the art, in terms of machining methods, types of tools and the various materials.
Technical Data Value Test method
Density at 15°C g/ml 0,88 DIN 51 757
Viscosity at 40°C mm²/s 22 DIN 51 562
Flash Point °C >190 DIN ISO 2592
Coppercorrosion 1 (3h/100°C)
All values are approximate values